Contact
Home/Insights/

Oilfield Supply

Oilfield Supply

Guide

Critical spares: the parts you should never wait for

Holding everything wastes capital, but waiting for the wrong part can stop a plant. A criticality-led approach puts the right spares on the shelf.

September 8, 2026

4 min read

KARR technical team
Critical spares: the parts you should never wait for
At a glance
  • Spares decisions should follow an up-to-date equipment criticality assessment, not an inherited parts list.
  • Single points of failure often justify holding expensive, slow-moving spares because of the downtime they prevent.
  • A lead time versus consequence matrix shows which parts to stock, secure by agreement or buy on demand.
  • Heat, humidity and dust shorten shelf life, so preservation and regular review matter as much as quantity.

When a critical pump seal fails or a control valve actuator stops responding, the question is not whether a spare exists but where it is. If the answer is that it is on order or still with the supplier, the plant may be running at reduced capacity or shut down entirely while it waits. On remote sites, the wait can be measured in weeks.

Holding everything is not the answer either. Large spares inventories tie up capital, take up warehouse space and can deteriorate on the shelf. The aim is to hold the right parts, in the right condition, and to know why each one is there.

Start with criticality, not the parts list

Spares decisions should follow from the criticality of the equipment they support. A criticality assessment ranks assets by the consequence of their failure on safety, environment, production and cost. Many operators already hold this in their maintenance management system, though it is often out of date or not linked to spares holdings.

Once equipment is ranked, the spares question becomes clearer. For highly critical equipment, look at which components are likely to fail and what happens if they do. For lower criticality equipment, holding fewer spares and accepting a longer repair time may be perfectly reasonable.

Find the single points of failure

Single points of failure deserve particular attention. These are components whose failure stops a system with no redundancy to fall back on. Examples might include a feed pump without a standby, a unique control card, or a specialised seal in a compressor with no spare unit. Process and maintenance engineers walking through each critical system together will usually find more of these than the records suggest.

Spares for single points of failure are often the most valuable items in the store, even if they are rarely used. Their worth is measured in the downtime they prevent, not in how often they move.

Lead time against consequence

A simple matrix helps to prioritise. Plot each candidate spare by the time it takes to obtain on one axis and the consequence of not having it on the other.

  • Long lead, high consequence: these are the parts you should never wait for, so hold them on site or in a guaranteed nearby pool.
  • Short lead, high consequence: hold a minimum quantity or secure a supply agreement with assured delivery times.
  • Long lead, low consequence: consider holding, but weigh the cost against alternatives such as repair or substitution.
  • Short lead, low consequence: generally buy on demand rather than stock.

Lead times should reflect the real route to site, including manufacture, inspection, shipping, customs clearance and final transport, not just the supplier's quoted delivery to their own dispatch point.

The cost of a critical spare is visible on the balance sheet; the cost of not having it only appears when it is too late.

Storage and preservation in hot climates

A spare that has deteriorated in storage is no better than no spare at all. Heat, humidity and dust at Gulf and North African sites accelerate many forms of degradation. Elastomer seals and O-rings can harden or crack, greases can separate, electronic components can be affected by heat and moisture, and bare steel surfaces can corrode quickly in coastal air.

Good practice includes climate-controlled storage for sensitive items, sealed packaging with desiccants, periodic rotation of shafts on stored rotating equipment as the OEM recommends, and clear records for time-limited items. Shelf-life limits come from the manufacturer and should be tracked, with items inspected or replaced before they expire. A spare that cannot be trusted when it is taken off the shelf creates a second emergency on top of the first.

Shared pools and review cycles

Some critical spares are expensive and rarely needed. Where several sites or operators use the same equipment, shared pools or vendor-held stock can provide access without each site holding its own. These arrangements need clear agreements on ownership, condition, call-off times and replenishment.

Spares holdings also need regular review. Equipment is replaced, suppliers change and lead times shift. A structured review might follow these steps:

  1. Update the equipment criticality register and confirm which assets are in scope.
  2. Check each critical spare against the current equipment model and part number.
  3. Confirm current lead times and supply routes with suppliers.
  4. Inspect stored items for condition, preservation and remaining shelf life.
  5. Remove obsolete stock and add any new gaps identified.

Repeating this at a set interval, and after any major plant modification, keeps the list relevant and stops obsolete stock from crowding out what is genuinely needed.

A practical first step

Choose your five most critical items of equipment and ask, for each one: if the most likely component failed tomorrow, where is the replacement and how long would it take to fit? The answers will show where your spares strategy needs work. KARR's oilfield supply team can help identify, source and manage critical spares.

Topics

Critical spares, Reliability, Inventory management

From insight to site
Want this applied to your assets?
Talk to our team
Keep reading

More insights.

View all insights →